HINGE BUTT, U/I PG (2) AWARDED IAW NSN: 5340-00-664-6974 HINGE, BUTT: SHALL CONFORM WITH ANSI/BHMA STANDARD…

Public award description

HINGE BUTT, U/I PG (2) AWARDED IAW NSN: 5340-00-664-6974 HINGE, BUTT: SHALL CONFORM WITH ANSI/BHMA STANDARD A156.1, IDENTIFYING NUMBER A8173, WITH THE FOLLOWING CHARACTERISTICS: TYPE - FULL, TRANSOM OR MORTISE HINGE, STANDARD WEIGHT, WITH PLAIN BEARING MATERIAL - STEEL, CORROSION RESISTANT, WITH BRASS PIN OPEN SIZE - 2 X 2 INCH (NOMINAL) THICKNESS - 0.083 INCH (NOMINAL) MOUNTING HOLES - 6 SCREW HOLES TOTAL PER HINGE SET, (3 PER HINGE HALF) FINISH - ANSI A156.18 CODE 603 UNIT OF ISSUE - PG (TWO (2) HINGES PER PACKAGE) COPIES OF ANSI/BHMA STANDARDS ARE AVAILABLE FROM BUILDING HARDWARE MANUFACTURERS ASSOCIATION, INC., 355 LEXINGTON AVENUE, NEW YORK, NY 10017 OR THE AMERICAN NATIONAL STANDARDS INSTITUTE, INC., 11 WEST 42ND STREET, NEW YORK, NY 10036. ALL HARDWARE REQUIRED FOR ATTACHMENT SHALL BE INCLUDED WITH THE HINGES. THE HARDWARE (PHILLIPS HEAD OR SLOTTED STYLE) SHALL BE DESIGNED FOR WOOD ATTACHMENT APPLICATION. THE HARDWARE SHALL PROPERLY FIT THE COUNTERSINK DEPTH AND DIAMETER OF THE HINGE ATTACHMENT HOLES. THE HARDWARE SHALL HAVE SUFFICIENT LENGTH AND DIAMETER COMMENSURATE WITH THE INTENDED LOAD DESIGN OF THE HINGE. THE FINISH REQUIREMENTS OF THE HARDWARE SHALL BE THE SAME AS THE BASIC HINGE. PRODUCT CONFORMANCE. THE PRODUCTS PROVIDED SHALL MEET THE SALIENT CHARACTERISTICS OF THIS DESCRIPTION, CONFORM TO THE PRODUCER' S OWN DRAWINGS, STANDARDS, AND QUALITY ASSURANCE PRACTICES AND BE THE SAME PRODUCT OFFERED FOR SALEIN THE COMMERCIAL MARKET. THE GOVERNMENT RESERVES THE RIGHT TO REQUIRE PROOF OF SUCH CONFORMANCE. MARKING: SHIPMENTS TO GSA AND OTHER CIVILIAN AGENCIES SHALL BE MARKED IN ACCORDANCE WITH FED-STD-123. SHIPMENTS TO THE DEPARTMENT OF DEFENSE (DOD) SHALL BE MARKED IN ACCORDANCE WITH MIL-STD-129. PREPARATION FOR DELIVERY: THE ITEM(S) SHALL BE PACKAGED AND PACKED TO AFFORD ADEQUATE PROTECTION AGAINST PHYSICAL DAMAGE DURING SHIPMENT FROM THE SUPPLIER TO THE FIRST RECEIVING ACTIVITY. THE PACK SHALL COMPLY WITH THE RULES AND REGULATIONS APPLICABLE TO THE MODE OF TRANSPORTATION. THE PACKAGE SHALL BE THE SAME AS THAT NORMALLY PROVIDED BY THE SUPPLIER. IN THE EVENT A PALLET OR SKID IS USED FOR SHIPPING, THE FOLLOWING NOTICE SHALL APPLY: NOTICE OF SPECIAL REQUIREMENTS FOR SHIPMENT TO ALL COUNTRIES THAT HAVE ENDORSED THE IPPC GUIDELINES FOR TREATMENT OF NON-MANUFACTURED WOOD PACKAGING: THE INTERNATIONAL PLANT PROTECTION CONVENTION (IPPC) HAS APPROVED AND PUBLISHED ON MARCH 15, 2002, GUIDELINES FOR REGULATING WOOD PACKAGING MATERIAL IN INTERNATIONAL TRADE . COUNTRIES ENDORSING THE IPPC GUIDELINES ARE FOUND AT HTTP://WWW.APHIS.USDA.GOV/PPQ/SWP/. CLAUSE D-FSS-468 REQUIRES NON-MANUFACTURED WOOD PALLETS AND OTHER NON-MANUFACTURED WOOD PACKAGING MATERIAL USED IN SHIPMENTS DESTINED TO IPPC COMPLIANT COUNTRIES REQUIRE THE APPROPRIATE WOOD TREATMENT. ADDITIONALLY, SHIPMENTS DELIVERED TO DOD DISTRIBUTION FACILITIES OR FREIGHT CONSOLIDATION POINTS FOR EVENTUAL DELIVERY TO OR THROUGH EU/IPPC COUNTRIES SHALL COMPLY WITH APPLICABLE DLA REGULATIONS AND PROCUREMENT LETTER PROCLTR 02-17.