REFLECTOR, INDICATING, CLEARANCE, REFLEX TYPE, RECTANGULAR WITH ROUND CORNERS AWARD MADE IAW RFQ# 9905-00-1…

Public award description

REFLECTOR, INDICATING, CLEARANCE, REFLEX TYPE, RECTANGULAR WITH ROUND CORNERS AWARD MADE IAW RFQ# 9905-00-182-5041 DATED 04/19/12 INCORPORATED AND MADE PART OF THIS AWARD L5 ***********SHIP TO ADDRESS*********** DLA DEFENSE DIST DEPOT TRACY DEPOT TRUCK CONTROL 209-839-4518 /4519 25600 CHRISMAN ROAD WHSE 30 CCP TRACY, CA 95304-5000 ************************************************************************ REFLECTOR, INDICATING, CLEARANCE: SHALL BE IN ACCORDANCE WITH U.S. ARMY TANK AUTOMOTIVE CENTER DRAWING 11614174 DATED FEBRUARY 16, 1970 WITH THE FOLLOWING CHARACTERISTICS: P/N 11614174-1 UNIT OF ISSUE - EA (EACH) EXCEPTIONS TO DRAWING REQUIREMENTS: 1) IN TABLE I. REFLECTIVE INTENSITY VALUES, REPLACE COLUMN HEADING AS FOLLOWS: FOR DIVERGENCE ANGLE SUBSTITUTE OBSERVATION ANGLE ; FOR INCIDENCE ANGLE SUBSTITUTE ENTRANCE ANGLE ; FOR INTENSITY VALUE, MINIMUM . . . ETC. SUBSTITUTE PHOTOMETRIC PERFORMANCE,MINIMUM, SPECIFIC INTENSITY PER UNIT AREA (CANDLES PER FOOT-CANDLE PER SQUARE FOOT) 2) DELETE REFERENCE TO FED SPEC L-S-300 IN PARAGRAPH 4.5.2.4 AND SUBSTITUTE: ASTM D4956, TYPE II 3) 0.10-0.15 EDGE HEAT SEAL NOT REQUIRED WHEN 3M SCOTCHLITE BRAND REFLECTIVE SHEETING, HIGH INTENSITY GRADE, PART NUMBER 3872 IS USED. 4) DELETE REFERENCE TO TT-X-916 IN PARAGRAPH 4.5.2.8 AND SUBSTITUTE: ASTM D5211. 5) WEATHERING: UNLESS OTHERWISE SPECIFIED, A CERTIFICATE OF CONFORMANCE MAY BE ACCEPTABLE AS PROOF OF CONFORMANCE TO THE TEST REQUIREMENTS FOR WEATHERING I LIEU OF LOT-BY-LOT TESTING. THE CONTRACTOR SHALL HAVE AVAILABLE FOR REVIEW EVIDENCE THAT THE WEATHERING TEST SPECIFIED HAS BEEN PERFORMED. A TEST REPORT FROM A LABORATORY ACCEPTABLE TO THE GOVERNMENT STATING THAT THE REFLECTOR TAPE HAS BEEN TESTED AND HAS PASSED THE WEATHERING TEST SPECIFIED, MAY BE ACCEPTABLE AS EVIDENCE OF CONFORMANCE. PRODUCT CONFORMANCE: THE PRODUCTS PROVIDED SHALL MEET THE SALIENT CHARACTERISTICS OF THIS ITEM PURCHASE DESCRIPTION, CONFORM TO THE PRODUCER' S OWN DRAWINGS, SPECIFICATIONS, STANDARDS, AND QUALITY ASSURANCE PRACTICES, AND BE THE SAME PRODUCT OFFERED FOR SALE IN THE COMMERCIAL MARKET. THE GOVERNMENT RESERVES THE RIGHT TO REQUIRE PROOF OF SUCH CONFORMANCE. PREPARATION FOR DELIVERY: THE ITEM(S) SHALL BE PACKAGED AND PACKED TO AFFORD ADEQUATE PROTECTION AGAINST PHYSICAL DAMAGE DURING SHIPMENT FROM THE SUPPLIER TO THE FIRST RECEIVING ACTIVITY. THE PACK SHALL COMPLY WITH THE RULES AND REGULATIONS APPLICABLE TO THE MODE OF TRANSPORTATION. THE PACKAGE SHALL BE THE SAME AS THAT NORMALLY PROVIDED BY THE SUPPLIER. IN THE EVENT A PALLET OR SKID IS USED FOR SHIPPING, THE FOLLOWING NOTICE SHALL APPLY: NOTICE OF SPECIAL REQUIREMENTS FOR SHIPMENT TO ALL COUNTRIES THAT HAVE ENDORSED THE IPPC GUIDELINES FOR TREATMENT OF NON-MANUFACTURED WOOD PACKAGING: THE INTERNATIONAL PLANT PROTECTION CONVENTION (IPPC) HAS APPROVED AND PUBLISHED ON MARCH 15, 2002, GUIDELINES FOR REGULATING WOOD PACKAGING MATERIAL IN INTERNATIONAL TRADE . COUNTRIES ENDORSING THE IPPC GUIDELINES ARE FOUND AT HTTP://WWW.APHIS.USDA.GOV/PPQ/SWP/. ADDITIONALLY, SHIPMENTS DELIVERED TO DOD DISTRIBUTION FACILITIES OR FREIGHT CONSOLIDATION POINTS FOR EVENTUAL DELIVERY TO OR THROUGH EU/IPPC COUNTRIES SHALL COMPLY WITH APPLICABLE DLA REGULATIONS AND PROCUREMENT LETTER PROCLTR 02-17. MARKING: SHIPMENTS TO GSA AND OTHER CIVILIAN AGENCIES SHALL BE MARKED IN ACCORDANCE WITH FED-STD-123. SHIPMENTS TO THE DEPARTMENT OF DEFENSE (DOD) SHALL BE MARKED IN ACCORDANCE WITH MIL-STD-129.